DIY Budget Japanese Lantern
This project is easy and affordable and can add a lovely unique accessory to your home. You can buy the tools you need from any art and craft store, office supply store or thrift shop.
Time:
3-4 hours (including dry time for glue)
Materials
Seven standard size Manila folders
12 bamboo chopsticks or wooden skewers
Coloured tissue paper (or any form of decorative, textured paper)
Craft glue
Decoupage medium - such as Mod Podge etc
Hot glue gun and glue sticks
Pencil
Ruler
Scissors
Method
First, trim the curved corners and tabs off the side of all seven of the folders with a paper cutter, or craft knife, and straight edge. The width of each folder from spine to edge should be 8" after the curved corners are trimmed off.
Reserve three of these folders, and cut one at a time perpendicular to the spine of the folder, so that you're cutting four equal-sized strips which are folded in half at the spine. The strips will be approximately 3 inches in width, but measure the width and divide by 4 to get exact measurement. You will have a total of twelve strips, which will form the accent sections above and below the main body of the lamp shade.
Now, take one of your full-sized folders, and open it up flat on your work area. Spread some light beads of glue across one side of the open folder, and then take another folder, and open it up, and lay one side on top of the side that you just put glue on.
Keep repeating this process until you've used all the four whole folders. The last panel should be glued to the very first panel on the first folder you started with, making a complete square that you can carefully stand up and let dry for a while until it's sturdy.
Repeat this process with the twelve strips you cut earlier, making three squares.
One of the smaller squares will be the anchoring piece for the pendant-light kit, so before proceeding to any other step, take time to measure the top of your light bulb-housing to get an idea of it's diameter. You will make a "grid" of criss-crossed skewers, which will create an inner square opening small enough to keep the light bulb housing from slipping higher up but big enough to allow the electrical plug to fit through. So estimate this measurement, and jot it down if you need to.
Find the middle of each square section with the help of a ruler. Mark the vertical and horizontal center points. Make light pencil marks to mark out two equidistant spots from the center and then puncture holes there, and also repeat this on the opposite side. Use an awl, skewer, or whatever you can find to help you puncture the holes for the criss cross wood skewers to pass through. (See pictures.) On the adjacent sides the markings will have to be moved down about a quarter of an inch to take into account the thickness of the skewers/ chop sticks so they can overlap each other. Erase the pencil markings so they don't show through the tissue paper. Test putting the four skewers into this piece to make sure they fit, and then remove them again so you can decoupage on the tissue paper to these smaller squares. Let dry for a while, and then insert the skewers through the holes again, and use pliers to pinch off the sharp ends of the skewers.
Next, use decoupage medium to cover the outside of your lamp shade with tissue paper, or some kind of textured rice paper. You can crinkle it slightly for a textured effect. Give yourself a little margin on the top and bottom to crease and fold "into" the lamp to finish the top and bottom edges. Tissue paper gets more opaque when it is layered, so mind that you don't accidentally overlap it, if you don't want darker areas on your shade.
Keep in mind that the manila folders are very opaque and golden-toned when lit, so for best results I'd use light, warm colours of paper on the outside. One more word of caution: my first prototype lamp turned out quite nice, and I was very pleased with it, until I realized that there were printed logos on the inside of the folders that were shining through the paper when the lamp was lit. So take that into consideration, and try to find folders that don't have obvious printed logos on them, or else plan to paint a design or paste some kind of cloth ribbon around the middle of the lamp where the logo is to conceal it.
Heat up your hot glue gun, and line up all the pieces on the table. Study the picture of the finished lamp shade to see how to space them out. There is one square on top, and then the skewered-square is second down from the top so that the light-bulb housing is dropped into the middle of the lamp as much as possible. In the middle is the main body of the lamp, and then one more square at the bottom.
When the glue gun is heated up, start from the "bottom" of the lamp shade. Line up a skewer or chop stick with the bottom corner of the bottom-most square, and hot glue it on the inside corner edge, and work your way around with the other three sticks.
Now slip the open ends of the skewers up into the main body of the lamp, and glue them into the inside corners. Now you will have used up four of the chop sticks or skewers.
Then turn your lamp around and glue the next four skewers into the top half of the inside edges of the main part of the lamp so that they extend out about 7" above the edge of the main part of the lamp.
Leave about an inch of visible wood skewer, and slip on the square that has the criss-cross skewer construction. Glue them inside the corners, taking care to space it evenly on all four corners so it doesn't look crooked.
Finish up with the top-most square, and glue the ends of the skewers into place.
Thread the plug-end of your light-bulb kit through the bottom of the lamp shade, and up through the middle of the criss-crossed skewers. The end of the light kit should stop there, if you've measured correctly, and suspend down from that point. Hook up your light with a hook screwed into your window sill or ceiling.
And there you have it! A wonderful and original home made decoration to light up your house.
Categories
#DIY_Craft
#Recycling_Craft
#DIY
#Art_and_craft
%decornotes
256666 - 2023-07-20 00:39:05